technology

Cen-Tech digital multimeter

200views

How To Use Cen-tech Multimeter

Cen-Tech makes a few distinctive advanced multimeters, however you needn’t bother with discrete directions for every one. Multimeters made by Cen-Tech all have similar directions of utilization. On the off chance that you realize how to utilize the economical 98025 seven-work model, you can utilize all the others. The seven capacities allude to this current model’s capacity to gauge AC and DC voltage, current and obstruction, and its capacity to test diodes, semiconductors and batteries.

It makes it simpler to utilize with the goal that each new model won’t be excessively confounded.

Here’s a guide in how to utilize a computerized multimeter and its capacities by Cen-Tech.

Preparing to Use the Multimeter

Note the fundamental selector wheel on the facade of the multimeter. Utilize this wheel to choose the capacity you need and the affectability of the estimation you will make. You’ll see three jack inputs organized in a vertical line on the base right. They are checked – through and through – 10ADC, VΩmA and COM. The meter accompanies a couple of leads, one dark and one red, that fit into these jacks. On the left side, you’ll see a multipin semiconductor/hFE jack for testing semiconductors. You’ll additionally observe an On/Off catch. Turn this on to actuate the LED show.

Measuring Voltage and Current

To quantify current, change the red lead to the 10 ADC jack and leave the dark one in the COM jack. Turn the dial to the 10 amp (10A) territory, ensure the meter is on, contact the prompts the uncovered circuit wires and note the perusing. In the event that it’s underneath 0.2 amps, turn off the meter, place the red lead into the VmA jack and turn the dial one position counterclockwise to the 220m setting in the DC amp (DCA) territory. Turn on the meter and take another perusing. Keep turning the dial counterclockwise – right to 200 µ if important – to build the exactness of the perusing.

To gauge DC voltage, leave the red lead in the jack checked VΩmA and the dark lead in the jack stamped COM and turn the dial counterclockwise to the 1000 setting in the DC voltage area (DCV). Take the perusing by contacting the prompts the uncovered circuit wires. On the off chance that the perusing is under 200, move the dial to that setting. In the event that the perusing is under 20, move the dial to that setting. Continue turning the dial varying, right to 200 mV if vital, to get the most precise perusing.

To gauge AC voltage, pivot the selector to highlight 750 in the AC voltage area (ACV) at the top. Fitting the red lead into the jack stamped VΩmA and the dark lead into the jack checked COM. Contact the prompts the uncovered wires of the circuit you are trying and note the perusing. In the event that it is under 250 volts, turn the selector to the 250 setting in the AC voltage area to get a more exact perusing.

Measuring Resistance and Continuity

Electrical commotion must not upset the perusing. The circuit radiates a small current for estimating opposition. The meter should initially understand 0 so make a point to check the voltage work. Associate the dark test to the COM port and the red one to the VΩmA port. In the wake of turning the meter on, change the dial to 200 ohms with the omega image (Ω). Prior to beginning a perusing, ensure that the presentation peruses 0 by contacting the tips of the tests together. Interface the test prompts the wirings of the circuit and take the perusing. Turn the dial counterclockwise if the showcase demonstrated 1. Continue exchanging the dial until you get some different option from 1.

Set the dial to 200k ohms to quantify the circuit’s coherence comparatively to the opposition. It’s an open circuit if the presentation shows 1. Different readings implied that it’s a shut circuit.

Testing Diodes and Batteries.
Instructions to test diodes

Change the dial to the diode territory at the most reduced of ohms. We can test the voltage drop of a diode to decide whether it’s still in acceptable working request. Join the red test lead to the VΩmA. Do likewise with the dark test lead yet associate it to COM and run the meter. Associate the red test to the diode terminal while the dark connects to the next. The perusing will show in millivolts.

Test your batteries

The multimeter is equipped for testing batteries at AAA, AA, C-cell, 9V, and D-cell. At the top is the ACV zone. Switch the dial there and interface the dark lead to COM and the red to VΩmA port. Associate the tip of the dark lead to the negative terminal and the red lead tip to the positive terminal until an understanding surfaces. Try not to utilize this on a 6 and 12-volt vehicle batteries. A voltmeter is best for the errand.

Leave a Response